Latest topics
» Transmission Malfunction by yowa82 2017-12-28, 3:53 pm
» Fiesta Car Parts Price List
by Cilikering 2015-11-18, 11:57 am
» something wrong with the clutch..
by Cilikering 2015-11-16, 3:41 pm
» Fiesta-Engine die off
by ayubom 2015-11-02, 4:00 pm
» Ford Fiesta Wipers Replacement Enquiry
by pepsiman 2015-10-30, 5:05 pm
» Dual clutch problem!!!
by Cilikering 2015-10-16, 4:23 pm
» FORD AUDIO/Multimedia software update (OCT 2011) *WILL FIX IOS BT ISSUES**Updated Post*
by judesh 2015-09-17, 11:55 am
» Fiesta fail to start at first inition start engine
by Miley 2015-07-28, 2:56 pm
» Opinions needed on new Ford service centre in Penchala
by redwacko 2014-12-01, 11:45 pm
» Warranty check
by harmeet.21 2014-11-30, 11:41 am
How Seatbelts Work
3 posters
Fiesta Club Malaysia :: Ford Fiesta Hatchback & Sedan 2010 -2011 :: General Fiesta Talks :: Safety and Everything Else
Page 1 of 1
How Seatbelts Work
The Pretensioner
The idea of a pretensioner is to tighten up any slack in the belt webbing in the event of a crash. Whereas the conventional locking mechanism in a retractor keeps the belt from extending any farther, the pretensioner actually pulls in on the belt. This force helps move the passenger into the optimum crash position in his or her seat. Pretensioners normally work together with conventional locking mechanisms, not in place of them.
There are a number of different pretensioner systems on the market. Some pretensioners pull the entire retractor mechanism backward and some rotate the spool itself. Generally, pretensioners are wired to the same central control processor that activates the car's air bags. The processor monitors mechanical or electronic motion sensors that respond to the sudden deceleration of an impact. When an impact is detected, the processor activates the pretensioner and then the air bag.
Some pretensioners are built around electric motors or solenoids, but the most popular designs today use pyrotechnics to pull in the belt webbing. The diagram below shows a representative model.
The central element in this pretensioner is a chamber of combustible gas. Inside the chamber, there is a smaller chamber with explosive igniter material. This smaller chamber is outfitted with two electrodes, which are wired to the central processor.
When the processor detects a collision, it immediately applies an electrical current across the electrodes. The spark from the electrodes ignites the igniter material, which combusts to ignite the gas in the chamber. The burning gas generates a great deal of outward pressure. The pressure pushes on a piston resting in the chamber, driving it upward at high speed.
A rack gear is fastened to one side of the piston. When the piston shoots up, the rack gear engages a gear connected to the retractor spool mechanism. The speeding rack rotates the spool forcefully, winding up any slack belt webbing.
The idea of a pretensioner is to tighten up any slack in the belt webbing in the event of a crash. Whereas the conventional locking mechanism in a retractor keeps the belt from extending any farther, the pretensioner actually pulls in on the belt. This force helps move the passenger into the optimum crash position in his or her seat. Pretensioners normally work together with conventional locking mechanisms, not in place of them.
There are a number of different pretensioner systems on the market. Some pretensioners pull the entire retractor mechanism backward and some rotate the spool itself. Generally, pretensioners are wired to the same central control processor that activates the car's air bags. The processor monitors mechanical or electronic motion sensors that respond to the sudden deceleration of an impact. When an impact is detected, the processor activates the pretensioner and then the air bag.
Some pretensioners are built around electric motors or solenoids, but the most popular designs today use pyrotechnics to pull in the belt webbing. The diagram below shows a representative model.
The central element in this pretensioner is a chamber of combustible gas. Inside the chamber, there is a smaller chamber with explosive igniter material. This smaller chamber is outfitted with two electrodes, which are wired to the central processor.
When the processor detects a collision, it immediately applies an electrical current across the electrodes. The spark from the electrodes ignites the igniter material, which combusts to ignite the gas in the chamber. The burning gas generates a great deal of outward pressure. The pressure pushes on a piston resting in the chamber, driving it upward at high speed.
A rack gear is fastened to one side of the piston. When the piston shoots up, the rack gear engages a gear connected to the retractor spool mechanism. The speeding rack rotates the spool forcefully, winding up any slack belt webbing.
Re: How Seatbelts Work
nice! is it installed for all seat? or just driver?
yowa82- NON Verified Member
- Posts : 63
Join date : 2011-02-28
Re: How Seatbelts Work
So once the Pretensioner work its way up can it be reuse again? Or need to send for servicing?
teetaatee- NON Verified Member
- Posts : 139
Join date : 2011-03-08
Fiesta Club Malaysia :: Ford Fiesta Hatchback & Sedan 2010 -2011 :: General Fiesta Talks :: Safety and Everything Else
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum